How to change a flat tire step by step
Change a flat tire safely at the roadside with a step-by-step procedure covering a safe stopping place, the jack, loosening the lug nuts and fitting the spare, plus when to call for roadside help.
Most drivers can change a flat tire safely once they know the procedure. The hardest part is usually not the physical work but the setup: finding a safe place to stop, making the car stable and getting the spare out. Once the car is secure, the steps follow a clear order. Most people can change a tire in thirty minutes or so, provided they have a working jack, a lug wrench and a usable spare. Practicing the steps once in a driveway, before you need them, makes a real difference when you are on the shoulder of a busy road.
Your first priority is safety. As soon as you notice a flat, or a strong vibration and a pull to one side, slow down gradually and move to a safe place. Choose a flat, firm surface away from traffic, ideally a wide shoulder, a parking lot or a rest area. Avoid soft ground, slopes and areas near curves where drivers may not see you. Turn on the hazard lights, set the parking brake and place the transmission in park for an automatic or in first or reverse for a manual. If you have warning triangles or flares, place them behind the car at a safe distance, and if you are on a highway, consider calling for roadside assistance rather than working next to fast traffic.
Gather the tools and check the spare
You need the spare tire, the jack, the lug wrench and any locking lug nut key. Most cars keep these in the trunk under a floor panel, behind a cover or in a compartment under the rear seat. Some cars have a tire inflator kit instead of a spare, and some have a temporary spare that is limited to a short distance and a lower speed. Check the spare's pressure and condition before you need it. A spare that is flat or badly worn will not help you on the road, and a temporary spare has a speed limit printed on it that you should respect.
Read the owner's manual for the location of the jack points, which are reinforced areas of the frame near each wheel. Using the wrong point can damage the car or cause it to slip off the jack. Some cars have a special jacking point marked with a small notch or arrow.
Change the tire step by step
Follow these steps in order:
- Park on firm, level ground, set the parking brake and turn on the hazard lights.
- Place wheel chocks or a heavy object against the tire diagonally opposite the flat, if you have them.
- Remove the hubcap or wheel cover, if the wheel has one, and loosen each lug nut about a half turn while the tire is still on the ground.
- Position the jack under the jack point closest to the flat tire, and raise the car until the flat tire is just off the ground.
- Remove the lug nuts completely and keep them in a safe place, such as a hubcap.
- Pull the flat tire off the hub and lift the spare into position, aligning the holes with the studs.
- Replace the lug nuts by hand, then tighten them in a star pattern to seat the wheel evenly.
- Lower the car until the tire touches the ground, then tighten the lug nuts fully in the star pattern.
- Lower the car completely, remove the jack and check the lug nuts again for tightness.
- Store the flat tire and tools, and check the spare's pressure as soon as you can.
Tightening in a star pattern matters. Working around the wheel in a cross pattern pulls the wheel evenly against the hub, which prevents it from wobbling or coming loose. Use the lug wrench with steady pressure, and avoid standing directly beneath the car while it is raised on the jack. Keep your hands clear of the jack's pinch points, and never put any part of your body under the vehicle.
After the change
Drive carefully after changing to a spare. Follow any speed and distance limits on a temporary spare, and check the lug nuts again after about fifty miles or after the first short drive. A wheel that was not seated correctly can loosen over time, and rechecking is the simplest way to catch that problem early. Have the flat tire repaired or replaced, since a spare is meant only for a short time. A tire shop can often patch a puncture in the tread area, but a sidewall damage usually requires replacement.
Keep the tools and spare in the car, and check their condition every few months. Keep the jack and lug wrench in a place you can reach quickly. Many drivers also keep a simple checklist in the glove box, so that a stressful moment does not lead to forgotten steps.
When to call for help
Call for roadside assistance if the car is in a dangerous spot, if the jack is damaged or missing, if the lug nuts are seized or the lug wrench does not fit, if the spare is flat or if you feel unwell or unable to lift the tire safely. Many insurance policies and vehicle service plans include roadside help, and some car manufacturers offer it as well. Check your coverage before you need it, and save the assistance number in your phone.
Check the spare, the jack and the lug wrench this week. Locate them in the car, confirm the spare is inflated, and read the owner's manual section on the jack points so the tools are ready before the next flat.