Skip to content
← All articles
Car Trouble

How to jump-start a car safely

Jump-start a car with jumper cables or a portable jump starter using a safe connection order, the right checks before you begin and a clear procedure for disconnecting without creating sparks.

A man in a blue jacket waving while leaning on the hood of a white car parked on a driveway with jumper cables on the ground.

A jump start is a common way to get a car with a dead battery running again, and a dead battery often shows up at the worst moment, such as a cold morning or a parking lot after a long day. A jump start borrows power from another vehicle or a portable battery pack to turn the engine over until the alternator can recharge the battery. The procedure is safe when you follow the connection order exactly and watch for the hazards that cause injury, such as sparks near the battery and a reversed cable. Once you understand the logic behind each step, the process is straightforward.

Before you start, check that the situation actually calls for a jump. A slow crank, where the engine turns over reluctantly, suggests a weak battery. Clicking with no engine turnover can mean a dead battery or a poor connection at the terminals. Lights that dim sharply when you turn the key, or no response at all, can also point to the battery. If you hear a single click and nothing else, check the battery terminals for corrosion or looseness before connecting cables, because a loose clamp can cause the same symptoms as a dead battery. Also make sure the two vehicles have compatible electrical systems, since most cars with a twelve-volt battery can be jumped from another car with a twelve-volt battery. Do not jump a hybrid or an electric vehicle unless its manual specifically allows it, and check the instructions for any car with a battery in an unusual location.

Gather the equipment and find a safe spot

You need a set of jumper cables with insulated clamps of adequate thickness, or a portable jump starter. Thicker cables carry more current with less heat, and a shorter cable works better than a very long one because it reduces voltage drop. Park the working vehicle close enough for the cables to reach both batteries without stretching, but do not let the two vehicles touch. Turn off both engines, set the parking brakes, and move the transmissions to park or neutral. Turn off the lights, the radio and the climate control in both cars. Put on gloves and eye protection if you have them.

Locate both batteries and the positive and negative terminals on each. Terminals are usually marked with a plus and minus sign, and the positive terminal often has a red cover. Some cars have the battery under a cover or in the trunk, and some have a remote jump post under the hood that you should use instead of the battery terminals. Consult the owner's manual if you are unsure.

Connect the cables in the right order

The connection order is the most important safety step. Follow it exactly:

  1. Attach one red clamp to the positive terminal of the dead battery.
  2. Attach the other red clamp to the positive terminal of the working battery.
  3. Attach one black clamp to the negative terminal of the working battery.
  4. Attach the last black clamp to an unpainted metal part of the dead car's engine or frame, away from the battery.

The last connection is made away from the dead battery because the battery can release flammable hydrogen gas during charging, and a spark at the battery could ignite it. Keep the clamps from touching each other or any metal part while you attach them. Make sure each clamp has a firm grip on clean metal, and wipe away any heavy corrosion first.

Start the working car and let it run for a few minutes, with the revs slightly raised. Then try to start the dead car. If it does not start after a few tries, stop and check the connections, because a poor connection is a common reason for failure. Do not crank for more than about ten seconds at a time, and wait a minute between attempts so the starter does not overheat.

Disconnect safely after the start

Once the dead car starts, remove the cables in the reverse order of connection. First remove the black clamp from the engine of the car that was dead. Then remove the black clamp from the working battery. Next remove the red clamp from the working battery, and finally remove the red clamp from the car that was dead. Keep each clamp away from the others while you remove them.

Let the car that was dead run for at least fifteen to twenty minutes, or drive it for about half an hour, so the alternator can recharge the battery. A short trip around the block may not restore enough charge, and the car may fail to start again the next time. If the battery dies again quickly, it may need testing or replacement, since a battery that will not hold a charge is a common cause of repeated failures.

A portable jump starter

A portable jump starter is often simpler and safer than a second car. Charge the unit fully before you need it, and follow the manufacturer's instructions for connecting the clamps to the dead battery. Most units use the same color-coding and a similar connection order, and many include safety features that prevent a reversed connection from delivering power. Store the unit in a cool, dry place, and recharge it periodically, since a jump starter that has been left discharged for months may not start the car.

This week, check that your jumper cables or jump starter are in the car and look at the battery terminals for corrosion. If the battery is more than a few years old and has needed a jump before, have it tested at a shop before the next failure.