How to fix a door that sticks or will not latch
Find out why a door sticks or fails to latch, then adjust the hinges, the strike plate and the door itself with basic tools, following a step list that checks the cause before you make changes.
A door that rubs on the frame or will not close fully is more than an irritation. It can make a room harder to secure, let drafts in and wear out the hinges faster. The good news is that most sticking and latching problems come from a few predictable causes, and they can be corrected with a screwdriver and a little patience. Before you adjust anything, however, it helps to understand whether the problem comes from the door, the frame, the hinges or the house settling over time. Diagnosing the cause first prevents you from making the wrong adjustment and making the problem worse.
Start by observing the door in action. Open and close it slowly, and watch where it rubs. A rub mark on the top corner on the latch side, often with a wider gap at the top on the hinge side, usually means the door has sagged on its hinges, most often because the top hinge screws are loose. A rub near the latch side means the door is too wide for the opening or that the strike plate is misaligned. A gap at the top that changes as the door moves can suggest the frame has shifted. Check the hinges for loose screws, which can cause the door to drop. Also look at the humidity in the room, because wood doors can swell in damp weather and shrink in dry air, and that movement can make a door stick only at certain times of year.
Check the hinges and the screws
Loose screws are the most common cause of a sagging door, and they are the easiest fix. Tighten every screw in the hinges, and replace any that are stripped with longer screws if the design allows. Longer screws, which reach into the framing stud behind the jamb, provide a much stronger hold than the short screws that come with most hinges. Use a screwdriver that fits the screw head snugly, and avoid overtightening, which can strip the wood.
If the door still sags after the screws are tight, the hinges may be worn or the wood around them may be loose. Remove one hinge at a time to avoid letting the door drop, and place a wedge under the door if needed. Fill the old screw holes with wood glue and short wooden toothpicks, let the glue dry and then drive the screws back in. For a door that sags badly, a larger hinge or a hinge repair kit may be the right fix.
Adjust the strike plate
If the door closes but will not latch, the strike plate on the frame is often the problem. The strike plate is the metal piece that receives the latch bolt. Close the door slowly and look at where the latch meets the plate. If the latch hits the plate above or below the opening, the plate must move. Loosen the screws, reposition the plate slightly in the direction that lines up the latch, and tighten the screws again. If the screw holes are stripped, use longer screws to reach the framing behind the jamb.
Sometimes the strike plate needs more than a shift. If the opening in the strike plate is damaged, replace the plate with one of the same style. If the latch bolt itself sticks or is worn, replace the latch assembly in the door. A deeper mortise in the frame may be needed if the new plate does not fit. Chisel the mortise carefully, and take off only a little wood at a time, because removing too much can weaken the frame. If you are not comfortable with this, a locksmith or carpenter can make the change quickly.
Plane or sand the door edge
When a door rubs on the frame along its side or top, the door may be slightly too large for the opening, especially after a change in humidity. Before you remove any wood, mark the rubbing spots with pencil or chalk, close the door, and check which spots are being scraped. Remove the door from its hinges if the work is extensive, and place it on a stable surface. Use a hand plane or sandpaper on a block to take off a small amount of wood, only from the marked spots, then check the fit again.
Work slowly, and remove only a small amount at a time. A door that is planed too much will leave a gap that lets in drafts and noise. Seal the exposed wood with primer and paint or a clear finish after you have finished, since bare wood absorbs moisture quickly and can swell again. For a heavy or solid wood door, consider whether a professional carpenter should do the work.
Adjust in this order: screws, plate, then wood
- Watch the door move and note where it rubs or where the gap appears.
- Tighten every hinge screw and replace stripped screws with longer ones.
- Check whether the door sags, and repair worn hinge holes if needed.
- If the latch misses the plate, reposition the strike plate and tighten the screws.
- If the plate is damaged, replace it and adjust the mortise carefully.
- Mark any rubbing spots and remove a small amount of wood only where needed.
- Seal any bare wood and recheck the fit after the finish dries.
Most doors can be adjusted without major work, and the screws and strike plate fix the majority of problems. Start by tightening the hinge screws today and testing the latch, since that single check often solves the problem without any other changes.