How to fix a running toilet
Find out why a toilet keeps running and fix the flapper, fill valve or chain with basic tools, following a step list that tests each part before you buy a replacement.
A running toilet almost always comes down to the flapper, the chain or the fill valve, and it quietly wastes water every day. Water trickles from the tank into the bowl constantly, and in some cases the leak can waste hundreds of gallons a month without any visible sign on the floor. The repair is usually inexpensive and within reach of most homeowners. The cause is one of three parts inside the tank: the flapper that seals the drain, the fill valve that refills the tank, or the chain that links the handle to the flapper. Finding which one has failed takes a few minutes of careful observation.
Start with a simple test. Remove the tank lid and set it somewhere safe, then add a few drops of food coloring to the water in the tank. Wait about fifteen minutes without flushing. If color appears in the bowl, water is leaking past the flapper, and the flapper or its seat needs attention. If the bowl stays clear, the problem is probably the fill valve, which keeps the water level too high, so water runs down the overflow tube. Many toilets also show a water level problem when the water sits close to the top of the overflow pipe. The coloring test takes minutes and avoids guesswork, which is why most plumbers recommend it first.
Check the chain and the flapper
Look at the chain that connects the handle lever to the flapper. If the chain is too tight, it holds the flapper slightly open, and water leaks continuously. If it is too loose, it can get caught under the flapper and prevent it from sealing. The chain should have a small amount of slack, usually about half an inch when the flapper is closed. Adjust it by moving the clip to a different link on the chain. Remove any extra slack by trimming the chain with pliers if needed.
Next, examine the flapper itself. Rubber flappers wear out over time and become stiff, warped or coated with mineral buildup. Hold the flapper and feel the seal, and look for cracks, soft spots or a ring of deposits. If the flapper looks worn, replace it. Flappers are sold in standard sizes, and the most reliable way to choose one is to take the old flapper to a hardware store and compare the size and the fitting. Many flappers are designed for a specific tank brand, so check the model before buying.
Replace the flapper
A flapper replacement is a straightforward task. Turn off the water supply valve behind the toilet, then flush to empty the tank as much as possible. Unhook the chain from the handle arm and the flapper ring. Detach the old flapper from the two posts or hinge pins that hold it in place, and check that the flush valve seat underneath is clean and smooth. Wipe away any mineral deposits with a cloth and a little white vinegar, and avoid harsh abrasives that can scratch the seat.
Attach the new flapper by snapping it onto the posts or pins. Connect the chain, adjust the slack as described above, and turn the water supply back on. Let the tank fill, then test with the food coloring method again. The bowl should stay clear when the tank is full and the water should stop after the tank refills. If the flapper still leaks, check that it sits flat on the seat and that nothing is caught beneath it.
Replace the fill valve if the water level is wrong
If the coloring test shows that the bowl stays clear but the water keeps running, the fill valve is the likely culprit. The fill valve controls how much water enters the tank, and a worn valve can allow the water level to rise above the overflow tube, which sends water down the drain continuously. Look at the float, which is either a ball on an arm or a cup on a rod. Set the water level so it sits about an inch below the top of the overflow tube, according to the adjustment on the valve. Many newer fill valves have a screw or a clip for this adjustment.
If the valve does not respond to adjustment or if the water keeps running even after adjustment, replace it. Fill valves are sold as universal or model-specific kits, and the installation involves disconnecting the water supply line, removing the old valve and mounting the new one. Buy a kit that matches your tank, and follow the manufacturer's instructions closely. Taking a photo of the existing installation before you start helps you reassemble the parts correctly.
Flapper, chain or fill valve: the order to check
- Remove the tank lid and perform the food coloring test.
- If color appears in the bowl, check the chain slack and inspect the flapper.
- Replace the flapper if it is worn, warped or coated with mineral deposits.
- If the bowl stays clear but water still runs, check the water level against the overflow tube.
- Adjust the float or replace the fill valve if the level is too high.
- Retest with food coloring after twenty minutes to confirm the repair.
Most running toilets are fixed with a flapper, a chain adjustment or a fill valve adjustment, and the whole job is often finished in under an hour. Run the food coloring test tonight, since that single check tells you which part to address and avoids buying parts you do not need.