How to patch a small hole in drywall
Patch nail holes and small drywall holes so they disappear under paint, following a step list that covers materials, filling, sanding and matching the wall finish.
A small hole in drywall is an easy repair, and it rewards patience more than skill. Nail holes from pictures, scuffs from furniture and small punctures from a doorknob can all be repaired with inexpensive materials and a little patience. The secret to a repair that disappears is not the filler itself but the preparation and the layering. Thin coats, careful sanding and a paint match do more for the final result than any special product. Most small holes can be patched in an afternoon, with the paint drying overnight.
First, assess the size and type of the damage. A nail hole, a dent or a hole smaller than about an inch across can usually be filled with spackling compound or lightweight joint compound. A hole larger than that, or one that has torn the paper face of the drywall, needs a patch that is applied over a backing, and a patch larger than a few inches may call for a larger section of drywall. Check the back of the hole if you can reach it, and look for wires, pipes or studs nearby. If there is any chance of an electrical wire or a plumbing line behind the wall, stop and consult a qualified contractor before cutting or patching.
Gather the materials
For most small patches you need a putty knife, a sanding block or sandpaper of medium and fine grit, a bucket of spackling or lightweight joint compound, a damp sponge, a primer and paint that matches the existing wall. For holes larger than a nail hole, add a self-adhesive mesh patch or a metal patch kit that covers the gap and gives the compound something to bond to. Keep a dust mask and eye protection nearby when you sand, because drywall dust is fine and gets everywhere.
Choose a spackling compound that is labeled for the job and that is easy to sand. Lightweight compounds sand more smoothly and shrink less, and they are a good choice for most households. Mix the compound to the consistency of soft peanut butter if you are using a powder form, following the package directions carefully.
Patch the hole step by step
Follow these steps in order:
- Clean the area with a dry brush or cloth to remove loose paper and dust.
- Remove any loose or crumbled edges with the tip of a putty knife, making the hole neat.
- For a hole larger than a nail hole, apply the self-adhesive mesh over the gap and press it firmly.
- Spread a thin layer of compound over the hole, pressing it in and feathering the edges out a few inches beyond the damage.
- Let the first coat dry fully, which usually takes several hours depending on the product and the humidity.
- Sand lightly with fine-grit paper, then wipe away the dust with a damp sponge.
- Apply a second thin coat, feathering it wider than the first, and repeat the drying and sanding.
- Prime the patch, since bare compound absorbs paint differently from the surrounding wall.
- Paint the patch with the matching color, using two coats if needed.
Thin coats are the key. A thick layer shrinks as it dries and can crack, and it takes longer to dry through. Two or three thin coats usually produce a smoother surface than one thick coat, and the sanding between coats keeps the surface level. If you see a ridge at the edge of the patch, add a feathered coat that extends further out and blend it into the wall.
Match the finish and avoid visible patches
The final look depends on the paint and the finish. A flat finish hides small imperfections better than a glossy one, which reflects light and shows every ridge. If the wall has a textured surface, such as an orange peel or a knockdown finish, the patch must be textured to match, which can be done with a sponge or a small roller of the right type. Practice on a piece of scrap drywall or cardboard before you texture the patch itself.
Paint color can differ slightly over time because older paint fades. Take a sample of the existing wall to the paint store and ask for a color match. For a larger repaint, it is often best to paint the entire wall or the entire section between corners, since a patch painted alone can show up in certain lighting. Let the paint dry fully before judging the result, because wet paint looks darker and different than it will look when dry.
Common mistakes and when to call a professional
The most common mistakes are applying the compound too thickly, sanding too aggressively and skipping primer. Sanding through the compound can expose the paper face of the drywall and create a new problem, so use light pressure and fine grit. Skipping primer leaves the patch looking dull next to the paint, and it often needs a second coat to match.
If the hole goes through to another room, if water stains surround it, or if the drywall is soft or crumbling, look for the cause before patching. Water damage can indicate a leak, and a hole that appears where a fixture or pipe runs should be checked by a professional. A large hole, or a repair that needs a new section of drywall, is usually a job for an experienced contractor.
Pick up the compound, mesh and primer this week and patch the smallest hole in the house first. Practicing on a single hole builds the skill, and it lets you judge the finish before you tackle a larger repair.