What to do when the check engine light comes on
Decide whether a check engine light needs attention now or can wait, using decision steps based on whether the light is steady or flashing, how the car drives and what a diagnostic scan can reveal.
The check engine light says so little that the first job is to judge how urgent the problem is. The light is part of the car's onboard diagnostic system, and it comes on when a sensor or component reports a reading outside its expected range. That can mean something trivial, such as a loose fuel cap, or something serious, such as a misfire that can damage the catalytic converter. The light itself does not tell you which. The useful response is to gather a little information and decide whether to drive carefully to a shop or to have the car towed.
The first step is to check whether the light is steady or flashing, because the two mean very different things. A steady light means the system has detected a fault that should be checked soon, but the car is generally safe to drive for a short distance if it behaves normally. A flashing light usually indicates an active misfire, which can send unburned fuel into the exhaust and overheat the catalytic converter. A flashing light calls for immediate action: ease off the throttle, avoid hard acceleration, and get to a service location as soon as it is safe, or stop and call for assistance if the engine runs roughly.
Decide how urgent the situation is
Use the car's behavior as a guide. If the engine runs smoothly, the car accelerates normally, the temperature gauge stays in its normal range and there are no unusual noises or smells, the problem is probably not an emergency. Check that the fuel cap is tight, since a loose or damaged cap is a common and inexpensive cause of a steady light. Tighten the cap, drive for a day or two, and see whether the light goes off on its own. Many lights reset after a few trips once the fault clears.
The situation is more urgent if the engine stumbles, idles roughly, loses power, shakes or makes a new knocking or ticking sound. Overheating, a sharp smell of fuel, smoke or a temperature warning light alongside the check engine light also calls for immediate attention. In those cases, stop driving as soon as it is safe and seek assistance. Driving a car that is misfiring or overheating can cause expensive damage in a short time.
Read the code if you can
An inexpensive code reader can show the fault code that the car stored when the light came on. Many auto parts stores will read the code for free, and some car owners buy a small handheld reader that connects to the port under the dashboard. A code points to a system, such as a particular cylinder misfire, an oxygen sensor reading or an evaporative emissions leak, but it is not a full diagnosis. Many codes have several possible causes, and a part replaced on the basis of a code alone may not fix the problem.
Write down the code and the date the light came on, and note whether the light was steady or flashing. That record helps a technician focus the diagnosis and reduces the time and cost of the repair. If the code is clear and the cause is obvious, such as a fuel cap, you may be able to address it yourself. If the code points to a complex system, have a qualified technician test it.
A decision sequence
Use these steps to decide what to do:
- Check whether the light is steady or flashing, and act at once if it flashes.
- Look at the engine's behavior, the temperature gauge and any other warning lights.
- Confirm that the fuel cap is tight and secure.
- Read the fault code, if you have a reader, and record the code and date.
- If the car runs normally, schedule an inspection within a few days.
- If the car runs roughly, overheats or loses power, stop safely and arrange transport.
When you take the car to a shop, describe the symptoms in plain terms, such as "the light came on this morning, the car feels normal, and the light is steady." Ask for the code, the cause and an estimate before any work begins. A reputable shop will explain what it found, show you the reading and tell you what can wait. It is reasonable to ask for a second opinion on expensive repairs, particularly when the diagnosis is not clear.
Keep in mind that the check engine light will not always go off after a repair. Some systems take several drive cycles to confirm that the fault is cleared, and a technician may need to reset the system after the repair. A light that returns soon after a repair should be taken back to the same shop, along with the records of the earlier work.
Note whether the light is steady or flashing, tighten the fuel cap and check the car's behavior on the next drive. If the light stays on and the car runs normally, book an inspection and bring the fault code with you.