Skip to content
← All articles
Small Home Fixes

How to stop a dripping faucet

Find the cause of a dripping faucet and replace the worn part, whether a washer, cartridge or O-ring, using a step list that covers shutting off the water and identifying the faucet type.

A smiling woman leaning over a bathroom sink while touching the faucet handle, with a small wrench and washer placed on the edge of the sink.

A dripping faucet is a small problem with a surprisingly large cost. A drip every second can waste thousands of gallons of water a year, and the constant sound can disrupt sleep. The fix is often inexpensive, and it usually involves replacing a worn rubber washer, a cartridge or an O-ring. Most people can complete the repair in under an hour with a few basic tools. The main decisions are identifying the type of faucet, turning off the water safely and buying the correct replacement part, which is easier when you bring the old one with you.

Begin by working out which faucet you have, since the repair depends on the design. A compression faucet has separate hot and cold handles that you turn several times to open, and it uses a rubber washer at the bottom of a stem. A cartridge faucet, usually with a single lever, uses a cylinder inside the body that controls the flow. A ball faucet has a rotating ball with openings that control water and temperature, and a ceramic disc faucet uses two discs that slide over each other. Look at the handle and the way it moves, and check the manufacturer's name on the body if it is visible. Knowing the type tells you which parts to look for and which tools you will need.

Shut off the water and protect the sink

Before you take anything apart, shut off the water supply. Look for the shutoff valves under the sink, and turn them clockwise until they stop. If the valves are stiff or do not close, shut off the main water supply to the house instead. Open the faucet to drain any water left in the lines. Place a towel in the sink or cover the drain with a rag so that a small part does not fall down the drain. Use a bucket or a container to catch any water that remains in the faucet body.

Take a photo of the faucet before you disassemble it, so you can reassemble the parts in the right order. Keep the screws and small parts together in a dish, since losing a spring or a seat can turn a simple repair into a trip to the store.

Find and replace the worn part

For a compression faucet, remove the handle by taking off the decorative cap and the screw that holds the handle in place. Unscrew the packing nut and lift out the stem. The washer sits at the bottom of the stem, held by a brass screw. Remove the screw and the old washer, and take the new washer to a hardware store to match the size and shape. Install the new washer, reassemble the stem and handle, and check that the faucet closes without drips. If the valve seat inside the faucet body is worn or pitted, it may need a seat-dressing tool or replacement, which many hardware stores can supply with instructions.

For a cartridge faucet, remove the handle and the retaining clip that holds the cartridge in place. Pull the cartridge straight out, noting the orientation of the notch or tab. Take the old cartridge to a store to find an identical replacement, since cartridges are specific to the manufacturer and model. Install the new cartridge with the same orientation, reassemble the parts and test the faucet. Many cartridge faucets also have O-rings on the body, and replacing those O-rings while the faucet is apart prevents leaks around the base.

For a ball or ceramic disc faucet, the repair often involves replacing the cartridge or the disc set, and the parts are more specific to the model. Look for the manufacturer's repair kit, which includes the seals and springs that wear out. Follow the diagram in the kit carefully, and keep all the springs in order. If the faucet is an older model or the parts are not available, replacing the entire faucet may be more practical.

Test and check the repair

Once the new part is installed and the faucet is reassembled, turn the water supply back on slowly. Open the faucet a little to flush out any debris, then close it and check for drips. If the faucet still drips, check that the new part is seated fully and that the springs and O-rings are in place. A small piece of grit on the seat is a common cause of a persistent drip, and cleaning the seat or flushing the line again often solves the problem.

Watch the base of the faucet for leaks after the repair. A leak at the base often means an O-ring or gasket is not sitting correctly. Tighten the mounting nut gently, and avoid overtightening, which can crack the plastic or damage the seal.

Washer, cartridge or O-ring: the order of repair

  1. Identify the faucet type by its handle and internal design.
  2. Shut off the water at the valves under the sink, or at the main if the valves fail.
  3. Drain the lines by opening the faucet, and cover the drain.
  4. Photograph the faucet and remove the handle and the internal parts in order.
  5. Take the worn washer, cartridge or O-ring to a hardware store to match it.
  6. Install the new part, reassemble and turn the water back on slowly.
  7. Test the faucet for drips and check the base for leaks.

A dripping faucet is one of the most rewarding repairs for a beginner, because the result is immediate and the parts are inexpensive. This weekend, identify the faucet type and check whether a repair kit is available for your model. Bringing the old part to the store is the most reliable way to buy the right replacement.